What Did You Do To Your Roxor This Weekend?

[Arizona Johnny]

That is one fantastic job on the top and trailer. Would love to see how your two piece doors connect\disconnect as I have been thinking of the same design.

 

[Roxasuras]

I finally got the new truck to pull my Roxor. Gonna take my niece up the Mtns this wknd in the Roxor.

 

[txroadkill]

I learned that the scangauge you can adjust the map reading to boost, so I now have a boost gauge

 

[Colderweather86]

Installed my sliders from Rick Cesso

 

[Roxasuras]

Installed my sliders from Rick Cesso

View attachment 9297

That looks really good.

 

[Colderweather86]

That looks really good.

Thanks man. I like the color offset. I'll eventually end up repainting the Roxor OD green to match them. Not a lot of tan in Alaska to blend in to.

 

[Dan H.]

What does that mean? This site isn't owned by FCA.

I copied the On The Rox tire carrier and did not want to offend them. My attempt at having a sense of humor.

 

[Fallacy]

Super-cool setup Fallacy! What part of NM were you visiting? I lived in Albuquerque for three years and loved it. Great mix of high desert and forest.

Randomly within the circle, we have much more to see and very good reasons to go back.
We spent 10 days in the area and could have easily tripled that time to do it justice.

Next time down there we intend to drive the New Mexico BDR with the Roxor and camper, the wife wants me to ride it on my Yamaha Super Tenere before she’s willing to commit to it.

New Mexico Backcountry Discovery Route (NMBDR) Map & Information

 

[Fallacy]

That is one fantastic job on the top and trailer. Would love to see how your two piece doors connect\disconnect as I have been thinking of the same design.

Three alignment pins on each upper door frame, they drop into the holes in the lower halves.
I built a set of racks for them to latch into on the drivers side inside fender, it’s a 2-3 minute job to remove or replace.

 

[Colderweather86]

Randomly within the circle, we have much more to see and very good reasons to go back.
We spent 10 days in the area and could have easily tripled that time to do it justice.

View attachment 9298

Next time down there we intend to drive the New Mexico BDR with the Roxor and camper, the wife wants me to ride it on my Yamaha Super Tenere before she’s willing to commit to it.

New Mexico Backcountry Discovery Route (NMBDR) Map & Information

View attachment 9298

In my opinion what you have circled that's the most beautiful and scenic part of the United States. I've been all over there. I'd love to have spent more time around Cortez before we moved from the SW.

 

[Colderweather86]

Installed my Cecco engine/xmsn and transfer case skid plates. Still need to drop the tank to do the fuel tank skid, but the tank is full.

 

[txroadkill]

Installed my Cecco engine/xmsn and transfer case skid plates. Still need to drop the tank to do the fuel tank skid, but the tank is full.

View attachment 9302

the tank has a drain plug on it.

 

[Roxasuras]

I took my girlfriend and niece to see a firework show with the Roxor last night at Eaglewood golf course, great time. Happy 4th. Everyone

 

[Buckpasser]

Built the cab and camper winter of 2019, 200 watts of solar on each with independent power systems in the Roxor and the camper.
It‘s been to 13 states so far and we’re loving it.

View attachment 9292View attachment 9293View attachment 9294View attachment 9295

View attachment 9292 View attachment 9293 View attachment 9294 View attachment 9295

That is really nice! I’m still contemplating what I want to do about a winter top. I’m just bikini for now, but got the Roxor for my trapping business and need a warmer, dryer solution.

 

[Colderweather86]

the tank has a drain plug on it.

I would have to wait for a copper crush washer to get here, and I want to drive it now.

 

[Arizona Johnny]

Three alignment pins on each upper door frame, they drop into the holes in the lower halves.
I built a set of racks for them to latch into on the drivers side inside fender, it’s a 2-3 minute job to remove or replace.

View attachment 9299

View attachment 9299

Simple like the old CJ’s, I like it. I assume one of the three is in the top rail of the body since your latch handle is in the lower half? That should take care of any wobble in the upper half? Can I ask what gauge aluminum you used?

 

[txroadkill]

I would have to wait for a copper crush washer to get here, and I want to drive it now.

I reused mine with no issues.

 

[Fallacy]

Simple like the old CJ’s, I like it. I assume one of the three is in the top rail of the body since your latch handle is in the lower half? That should take care of any wobble in the upper half? Can I ask what gauge aluminum you used?

All 3 pins are in the doors only.
i ordered .062 aluminum, they shipped .080”, they price matched what I had ordered so I went with the .080”

 

[Colderweather86]

Installed my new winch. Tomorrow we are heading out alone into the shitty trails.

 

[GPG]

installed the wiring for my roadshock front led light bar!