Max’s Roxor Build

[Max A.]

Lines run for the box. I need one more fitting to complete the system. That should be here today. The cooler fits nicely behind the grill. There is room for an inter cooler should I decide to go that way in the future.


Because I needed that fitting to move to the next step I spent some time making a body mount that I lost at hammers. Before you know it this whole roxor will be aluminum .

Sent from my iPhone using Tapatalk

 

[Roxasuras]

Nice work buddy that is super awesome.

 

[Kake America]

I can’t wait to see you running again, your ride looked like it just floated through the bumps at speed!

 

[Max A.]

I have an idea that I am going to try that will help with the ride quality in the desert.

Even with $4000 in king shocks they got too hot. The rears completely faded and where about 230 degrees at one point. (This has only ever been a problem at hammers, racing in the wide open desert for 12 hours. )

For starters I’m going to. 2.5 body shock in the rear. To match the fronts. I ordered new shock in January and they aren’t suppose to ship up till October. King is super backed up with custom orders.

Next I want to water cool them. IF I have time, the plan is to make water jackets and circulate coolant through a trans cooler to keep them cooler.

I’ve never seen this done so I’m not sure how effective it will be but I’m going to give it a try.



Sent from my iPhone using Tapatalk

 

[Roxasuras]

I have an idea that I am going to try that will help with the ride quality in the desert.

Even with $4000 in king shocks they got too hot. The rears completely faded and where about 230 degrees at one point. (This has only ever been a problem at hammers, racing in the wide open desert for 12 hours. )

For starters I’m going to. 2.5 body shock in the rear. To match the fronts. I ordered new shock in January and they aren’t suppose to ship up till October. King is super backed up with custom orders.

Next I want to water cool them. IF I have time, the plan is to make water jackets and circulate coolant through a trans cooler to keep them cooler.

I’ve never seen this done so I’m not sure how effective it will be but I’m going to give it a try.



Sent from my iPhone using Tapatalk

That is awesome ingenuity! Hope it works out. Cany wait to see the prototype

 

[Colderweather86]

Dude. Max. Holy smokes man. That power steering pump mount is B-E-A-UTIFUL! Make sure you save that file to press print once I blow up my new PS pump when the 60s and 37s go on next month.

 

[Max A.]

I expect a “Mitchell’s Roxor Build” thread.


Sent from my iPad using Tapatalk

 

[Colderweather86]

I expect a “Mitchell’s Roxor Build” thread.


Sent from my iPad using Tapatalk

I'm the worst at taking pictures of stuff while I'm working. I'll do my best. I pulled the trigger on 2 E lockers, gear sets and drive flanges yesterday. Going to pull the rear shafts tomorrow to count the splines and measure the length after I find they're 30 instead of 35 spline.

 

[Dan H.]

I have an idea that I am going to try that will help with the ride quality in the desert.

Even with $4000 in king shocks they got too hot. The rears completely faded and where about 230 degrees at one point. (This has only ever been a problem at hammers, racing in the wide open desert for 12 hours. )

For starters I’m going to. 2.5 body shock in the rear. To match the fronts. I ordered new shock in January and they aren’t suppose to ship up till October. King is super backed up with custom orders.

Next I want to water cool them. IF I have time, the plan is to make water jackets and circulate coolant through a trans cooler to keep them cooler.

I’ve never seen this done so I’m not sure how effective it will be but I’m going to give it a try.



Sent from my iPhone using Tapatalk

Sounds like you are talking about making a heat exchanger like on inboard boats. You might look at them to see if they can be copied or modified for your needs to cool the shock fluid.

 

[Max A.]

Yep similar concept.


Sent from my iPad using Tapatalk

 

[Kake America]

I hope you patent that and make at least a small fortune once you get it working.

 

[Max A.]

Hydraulic assist steering is done. It works wonderfully. It will turn my 35s with one finger sitting still, yet still give wheel feedback for a non tractor like driving experience. Worth the headaches and many, many pennies.

I had to replace an axle seal so I figured it was also a good time to upgrade some other parts while I had things apart.

Upped the king pin size from factory to about an inch pin on both top and bottom. Also installed ARP studs for piece of mind. I think the housing is my weakest link now and it’s not weak at 1/2 an inch thick tubes.

Factory vs the new pins and bearings.

Sent from my iPad using Tapatalk

 

[Max A.]

I had something super freaking cool show up today!!! I asked on On The Rox if they were able to make a set of custom aluminum fender armor kits to replace my steel set and they delivered! And quick. I can’t believe how fast they were able to switch gears and get these things pumped out for me. Made to my spec, .250 wall tubing and thick 3/16 plate. Now I need to practice my aluminum TIG skills before I touch these babies.

Sent from my iPad using Tapatalk

 

[Roxasuras]

That's pretty damn awesome, should be stout and pretty light.

 

[Max A.]

Welp got my first tig machine in the mail today. I think I’ll be hiring someone to get these fenders done. There no way I’m going to progress fast enough to get these things looking good for my Moab trip in a couple weeks.

Sent from my iPad using Tapatalk

 

[Spanky]

Welp got my first tig machine in the mail today. I think I’ll be hiring someone to get these fenders done. There no way I’m going to progress fast enough to get these things looking good for my Moab trip in a couple weeks.
View attachment 10751
View attachment 10752


Sent from my iPad using Tapatalk

How much aluminum have you ever welded Max? If you just started with Aluminum, it's not awful bro. If you been welding aluminum for years, I'd say yeah.... probably outta hire it out.

 

[Max A.]

First time picking up a tig torch since shop class in high school 15 years ago.


Sent from my iPad using Tapatalk

 

[Spanky]

First time picking up a tig torch since shop class in high school 15 years ago.


Sent from my iPad using Tapatalk

Well bud, I'm a CWI and API Inspector (mechanical integrity specialist) and I'm guessing you may be between 25 and 30.... so if you haven't touched aluminum in 10-15 years, I'm betting you will master that craft in the near future. But for the time frame your dealing with... might outta spring for case of beer, a handle good wiskey, a few large pizzas and get a fellow over to slick it on out for ya. ?

 

[Roxasuras]

First time picking up a tig torch since shop class in high school 15 years ago.


Sent from my iPad using Tapatalk

Wow, first time I tried to weld I almost welded my fingers together. Looks great man. ?

 

[Max A.]

Won’t learn unless you try…

Sent from my iPhone using Tapatalk