Fender flares

[Togo]

My windshield is from On the Rox Fab. It is not a CJ windshield. The on the rox fab windshield is built to fit against the roll bar.

Thanks

 

[Driver8]

View attachment 2138

Ok, this is a good shot of a Roxor but Im more interested in the old pickup with an Oryx sitting the back.

 

[Andydaniel1371]

View attachment 2138

I like the jack on the bumper! Where can a guy find this set up?

 

[quickshot]

I like the jack on the bumper! Where can a guy find this set up?

The bumper is from On the Rox. The jack mount is just a tube clamp jack mount sold at most 4X4 jeep suppliers. I like it. Think the mounts were around 80 bucks or so. the same clamps could be used to mount to roll bars etc. here's a link to crown 4wd supply. https://www.4wd.com/p/hi-lift-jack-adjustable-tube-mount-tm-750/_/R-BJDH-TM-750

 

[Campyman]

The bumper is from On the Rox. The jack mount is just a tube clamp jack mount sold at most 4X4 jeep suppliers. I like it. Think the mounts were around 80 bucks or so. the same clamps could be used to mount to roll bars etc. here's a link to crown 4wd supply. https://www.4wd.com/p/hi-lift-jack-adjustable-tube-mount-tm-750/_/R-BJDH-TM-750

I like the way it looks too. However, keep in mind if you ever get into a front end accident your jack will likely be damaged. I used to the universal hood mounts from eBay. They cost me around 20 bucks.

 

[quickshot]

Ok, this is a good shot of a Roxor but Im more interested in the old pickup with an Oryx sitting the back. long story behind the truck --and the oryx, ha hah The truck is a 51 chev, owned it since high school.

View attachment 3531

 

[RoxorYooper]

I ordered flares for Cj7 or CJ5, years 76 through 86 from crown auto---fit just fine.

What size is the hardware? I want to replace it with stainless.

 

[quickshot]

What size is the hardware? I want to replace it with stainless.

If you are referring to the flares, you can use any screws/bolts you want-----just match the screw size with the size of hole that will be drilled.

 

[Woodsman74881]

I used 10/32x3/4” a washer and locknut on mine. All stainless. Drilled holes took q tip with rust oleum rust inhibitor primer paint into holes and let dry. Then installed flares.

 

[RoxorYooper]

If you are referring to the flares, you can use any screws/bolts you want-----just match the screw size with the size of hole that will be drilled.

Obviously, but I don’t have the flares until Monday and would like to know the size so I can pick them up now. Unless you’re saying the flares don’t have predrilled holes.

 

[RoxorYooper]

I used 10/32x3/4” a washer and locknut on mine. All stainless. Drilled holes took q tip with rust oleum rust inhibitor primer paint into holes and let dry. Then installed flares.

?? I have some 5/16” x 3/4”stainless button head bolts already.

 

[Andydaniel1371]

Obviously, but I don’t have the flares until Monday and would like to know the size so I can pick them up now. Unless you’re saying the flares don’t have predrilled holes.

Just put mine on the other day...
So I took my screws to a fastener screw co. matching the size in stainless.
After drilling painted holes for rusting later
Maybe it's best to see what size is in ur kit first.

 

[RoxorYooper]

What size is the hardware? I want to replace it with stainless.

For anyone else asking this question the answer is “yes there are predrilled holes (28 total) and the biggest drill bit that can pass through the holes is 19/64”. I would keep the hardware around 5/8” in length.